Handguns - Latest Reports


Long Guns - Latest Reports


Special Purpose Guns - Latest Reports

Home Defense
Law Enforcement
Concealed Carry



Gun News

Gun Rights
Industry Notes
New Products

Special Reports

Converting Old Browning Model A-5s

Newer versions of this famous shotgun use roll pins instead of screws to hold certain action parts. Here’s how to convert early Auto-5s.

Glock Mods: An M1911 Man Branches Out

I’ve worked with the 1911 for many years, and sometimes that experience has been helpful with other pistols, such as the Browning Hi-Power, for example. Sometimes the differences between pistols are hard to spot, and other times we find similarities between handguns that at first seem very different. Another example: If you can work on the Savage 1910, you can work on the Astra 400, and you won’t be confused by the H&K P7M8. But the Glock? Ah, the Glock is an altogether different creature. Sometimes my 1911-based reasoning produces positive results with the Glock, and other times it does not. With the Glock so popular with law-enforcement and now proving itself in competition—winning the first top-class award at IPSC—we’re going to see more and more Glocks turned in for improvement. And at the very least, we should be familiar with the similarities and the differences between the Glock and “old Slabsides.”


Semi-Annual FBI Report Confirms Crime Down As Gun Sales Up

The FBI's semi-annual uniform crime data for the first half of 2013 confirms once again what the firearms community already knew, that violent crime has continued to decline while gun sales have continued to climb.

GunBroker.com Names January 2014's Best Selling Firearms

GunBroker.com has released its list of Top 5 best-selling firearms for January 2014, topped by Smith & Wesson's M&P semi-automatic pistol.

Gun Reports - Special Reports

Gun Reports Home >> Special Reports

Scope-Ring Alignment: A Critical Accuracy Factor

February 6, 2013

Printer Friendly | Email

As the owner of a firearm test range, I mount dozens of scopes each year. I get to see first hand how they perform, as well as the performance of scopes mounted by others. The two main complaints I hear about scopes usually center around those that fail to remain sighted in or group poorly on target. These complaints are usually very well founded.

Scope-Testing Device
Mounting a scope on this rigid scope-testing device and using a dial indicator shows how stresses between parts can cause misalign-ment of the scope. Even a .001-inch movement of the scope shifts the reticle a full minute of angle, or about an inch at 100 yards.

Most complaints about scope mounting are the direct result of poor scope-ring alignment and the accuracy-robbing stresses inherent between metal parts. These stresses pull and twist, causing the scope to move and to become misaligned. The scope never really settles down as bullet point-of-impact changes over time or even as a target group is being fired.

Further compounding the problem is the fact that there are perhaps a score of scope base and ring manufacturers, all trying to eliminate tolerance errors in their attempt to match the manufacturing specifications among the myriad of firearms out there being scoped. This is a daunting task, and the manufacturers are often unsuccessful.

Identifying and Solving
The Alignment Problem
In essence, what is happening as we mount a scope is a stacking of tolerances—the scope base to the firearm receiver, the rings to the base, and the scope to the rings. As close as today’s scope and firearms manufacturers have come in the elimination of tolerance errors, scope-ring alignment should be a fundamental part of scope mounting.

There is a sure way to precisely check the coaxial alignment of a pair of mounted scope rings. This is accomplished by using a set of sleeved scope-alignment rods. If used correctly, these precision alignment rods will readily show the slightest alignment error. (Alignment rods are available from Brownells.)

Scope-Alignment Rods
The sleeved scope-alignment rods are seen here mounted in position on a Winchester Model 70 rifle receiver using a Redfield base and rings. The sliding rods are pointing toward each other indicating good ring alignment.

Using Scope-Alignment Rods
As sure as you may feel about your ability to mount a scope correctly, you should always follow the scope manufacturer’s instructions in mounting the base and rings. Mounting systems vary, so pay close attention, particularly if you are not totally familiar with the system you’re installing. Be sure the base doesn’t rock or shift as it is pressed against the receiver. Then tighten the base screws alternately and evenly. Be sure no long screws protrude through the threaded holes in the receiver. Then, with the base mounted, follow the directions for mounting the rings. Where there are laterally opposing adjustment screws for windage adjustment on the scope base—like those on Leupold, Redfield, Conetrol, and others—try to have the rings evenly spaced from right to left. Don’t tighten these screws firmly at this time.

The two alignment rod sleeves can now be placed in the scope-ring saddles. They fit both 30mm and one-inch rings. Then place the scope ring caps in position and tighten the screws with moderate torque.

Both alignment rods are then placed in position with the pointers midway between the sleeves, barely touching. Then you can see if coaxial alignment exists. The two rod pointers should come together to ensure a coincident axis. If they aren’t coinciding, see if the movable rear ring can be moved right or left to improve the alignment. Once the pointers seem to be in near perfect contact, it’s time to test if the rings are truly coaxial. This is done by removing the shorter alignment rod, and checking to see if the longer alignment rod will enter the opposite sleeve. If this can be accomplished, there is absolutely no misalignment of the two rings. To my knowledge, there is no other way to check the precise coincident axis between the two rings.

Scope-Ring Alignment:
As described in the text, the longer of the two alignment rods slides through both sleeves, ensuring perfect ring alignment. Note the one-inch sleeves being used here with the 30mm diameter as an integral part of each sleeve.

It’s worth noting that 0.001 inch of scope movement will cause about one minute of angle of scope reticle movement on the target. So it’s easy to see why a poorly mounted scope, inherent with stress, will leave you pulling your hair.

Making Corrections
For Poor Ring Alignment
Where minimal misalignment is present between the rings, a simple reversal of the rings by rotating them 180 degrees often produces better alignment. Base shimming can also used, but I believe this is a compromising effort—a makeshift fix at best.

Using the scope-alignment rods to manipulate the scope rings can do wonders to align the rings. Here the rods are installed with points toward one another, and a reasonable manipulative force is used on the offending ring (or rings) to bring the pointers together. This can be performed on both rings in moderation. It actually reduces stresses as the rings are aligned. But don’t attempt too great a correction in this way.

Brownells also offers a scope-ring alignment lap. This tool actually removes metal by lapping and fitting the rings. Clymer Reamers offers what they call a “ring-alignment reamer” for the same purpose. This dual-end reamer is clamped lightly into the rings and rotated to align them.

Scope-Ring Alignment:
A Near scope-mounting system is used here to mount a Sightron 6.5-20X scope on a Remington Model 700 action. This is one of the most rigid scope-mounting systems made. It actually adds stiffness to the rifle receiver. Brownells’ scope-alignment rods were used to produce a stress-free scope mounting here.

In my experience, only a relatively small percentage of scope rings are mounted in true alignment. This results in stresses that cause accuracy deficiencies. Fortunately, scope rings can readily be checked for precise alignment, and are quite easily corrected where misalignment exists. Where the best accuracy is sought and scopes are expected to remain sighted, there’s no substitute for the proper alignment tools.

digg this reddit submit Newsvine DEL.ICIO.US